0531-83510047
13791000079

大家都在搜: 食品级输送带 大倾角输送带 切菜机输送带

当前位置: ag - 新闻中心 > 常见问题 > 常见问题

挡边输送带为何裙边与隔板先破损?

来源:ag国际亚游官网 时间:2019-12-23 16:03:07 浏览次数:
  侧输送带因为空间更小!低成本,广泛应用于各种物料的提升和输送。在实际生产中往往是裙边和隔断打破比其他多的地方,为什么呢?输送带为您找出原因!只有好的设备,好的管理才能做好产品!
  Side conveyor belt is widely used in lifting and conveying of various materials because of its smaller space and low cost. In actual production, skirt and partition are often broken more than other places. Why? Qingdao Jiaoliu? Conveyor belt will find out the reason for you! Only good equipment and good management can make products!
  一、损坏的主要原因:
  1、 Main causes of damage:
  1. 皮带轮的压力:
  1. Pressure of pulley:
  的大轮和小轮的线速度不同,但焊接大轮和小轮一起力量小轮的速度是一样的大轮子,这样小轮形式与裙子的顶部摩擦阻力;
  The linear speed of big wheel and small wheel is different, but the speed of welding big wheel and small wheel is the same, so the small wheel form and the top friction resistance of skirt;
  B.小轮直径大,裙子顶部被迫下压,加上阻力摩擦,裙子边缘会很快磨损开裂。
  B. The diameter of the small wheel is large, the top of the skirt is forced to press down, and with resistance friction, the skirt edge will soon wear and crack.
  2. 检查返程长辊的缺陷。从照片上看不出来。无论皮带是否张紧,如果皮带不张紧,会导致皮带在运行过程中上下跳动,撞到托辊,造成裙边开裂。
  2. Check the defects of return long roll. I can't see it in the picture. No matter whether the belt is tensioned or not, if the belt is not tensioned, it will cause the belt to run up and down, hit the idler, and cause the skirt to crack.
  3.短托辊与回程裙边的距离很小,短托辊的顶部直接接触并穿裙边。
  3. The distance between the short idler and the return skirt is very small, and the top of the short idler directly contacts and passes through the skirt.
  4. 护墙板顶部外侧有明显的缺角,说明护墙板与钢件有划痕和碰撞。
  4. There is obvious missing angle on the outside of the top of the wall panel, indicating that there are scratches and collisions between the wall panel and the steel parts.
  二世。改进建议:
  II. Suggestions for improvement:
  1、压带轮必须更换,小轮有单独的轴承,使其能独立自由转动;小轮直径减小,正常情况下,使其与裙顶不连接。
  1. The pressing pulley must be replaced, and the small pulley has a separate bearing, so that it can rotate independently and freely; the diameter of the small pulley is reduced, so that it is not connected with the skirt top under normal circumstances.
食品级输送带
  2. 如果回程长托辊与裙边接触,则可将长托辊放低,使裙边不与之接触;或者,抬高短托辊,这样裙子的顶部就不会碰到长托辊。
  2. If the return long idler is in contact with the skirt, lower the long idler so that the skirt is not in contact with it; or, raise the short idler so that the top of the skirt does not touch the long idler.
  3.调整短托辊末端与裙边之间的距离。在脱轨的情况下,托辊的一端不会随着裙边磨损。
  3. Adjust the distance between the end of the short idler and the skirt. In the case of derailment, one end of the idler will not wear with the skirt.
  三世。:
  III. a key:
  1. 输送带的裙边和隔板不得与钢材直接接触。凡有接触处,应采取改进措施消除接触点。
  1. The skirt and partition of the conveyor belt shall not be in direct contact with the steel. Where there is contact, improvement measures shall be taken to eliminate the contact point.
  2. 裙子的作用是防止布料向两边扩散;分离器的作用是输送物料,防止物料滑动,实现大角度输送。
  2. The function of skirt is to prevent cloth from spreading to both sides; the function of separator is to transport materials, prevent materials from sliding, and realize large angle transportation.
  3.维护原则为:
  3. Maintenance principle:
  a、如有损坏,检查是否与设备有直接接触;
  a. If there is any damage, check whether there is direct contact with the equipment;
  B)消除隐患。
  B) Eliminate hidden dangers.

产品中心 PRODUCT CENTER

联系我们CONTACT US

手机:13791000079(孙经理)
座机:0531-83510047
QQ(客服):136559297
地址:山东省济南市章丘区刁镇民营经济开发区

XML 地图 | Sitemap 地图